2010 Bmw X3 No Power To Obd Port

Spare fuses and a pair of plastic forceps are set in holders on the distributor box. Can you give me any more details about your issue.

Bmw Obd2 Port Location

Bmw only put the obd socket in to comply with new rules and regs that came out at the time and even then only made it as functional as the regs demanded so like Brian says you can only connect to the engine module and even then I think it is still limited to the point it is practically useless.

2010 bmw x3 no power to obd port. All done via the OBDII port following our VR Tuned Instructions Here we adjust the cars timing and fuel maps. Fuse Box behind the glove compartment. Do not connect to the body or chassis ground but to the battery terminal directly.

The OBD II plug is located at the bottom of the steering wheel. 30i Gasoline 231HP 2004. 2 Diesel 143HP 2010.

3 Gasoline 231HP 2003. Measure Pin 16 on OBD port it should has voltage when ignition key in position 2. Check out his past snowy photos and his more recent VR Tuned Flash Photos below.

See the rear of the cover for information on fuse assignment. Turn on the ignition. Here is the OBD.

Giving the X3 better throttle response more torque and better pull to the top end. The connector will always have power on these two pins regardless of the key position. 2010 2007 BMW X3 30si SAV.

There are two generations of OBD ports OBD1 and OBD-ii aka OBD2. Checked the fuses behind the glove box which was like performing surgery. For those driving Autobahn style we remove the speed limiter as well.

Go to the OBD2. Note that pin 5 has ground in the description but that is just for the communication signalling and not for power. 1 OBD II Port Not Working.

With the ignition on the voltage drop across the ground terminal should be 01 Volts or less. 30d Diesel 204HP 2004. 20 pin connector under the bonnet is the one to use and ignore the obd socket as it is a waste of time.

These issues include an incompatible obd2 scan tool bad fuses damage in the circuit board ECU and failed computer. Checked the wires and none are chafed. This allows you to read flash ECM via USB connection on a laptop.

There will always be 12v power between pin 4 and 16. Monday morning I went out to go to work and my car would not start it would just keep on. I am using a Vivid Racing OBD2 adaptor that converts the six pin connector on the X3 to a standard OBD2 type connection.

OBD connector location for BMW X3 E83 2003 - 2010 You will find below several pictures which will help you find your OBD connector in your car. CAN 11bit 500kb BMW X3. Its more likely that the chinese OBD dongles are shagged rather than a sudden partial failure of your OBD port.

You have a wiring issue with the fuse block if there is no power. 20D Diesel 177HP 2009. Remove the little plastic cover.

CAN 11bit 500kb BMW X5. Buy a ELM327 OBD-USB cable download free software scantool or easyobdii try to read it by yourself if the software cant recognize the hardware make sure you set the correct COM port and Baud Rate or just try all the possible combination 4. Turn on the scanner and select your BMW chassis.

It is also the primary location of tracking devices such as dongles as the port provides ongoing power to the device. I have given you a good place to start. If your ZGM gateway is bad then it means the modules in your car cannot communicate which cause all sorts of issues including power drains if modules are not being shut down the right way.

These cars are very complicated eclectically. Pin 16 on the ODB-II connector is specified as Battery Power or Battery Positive. Connect the positive DMM lead to DLC pin 4 and the negative DMM lead to the negative battery terminal using jumper wires if necessary.

Diesel 192 HP 2003. It is plugged into a dummy port to keep clean so that is what was confusing. Dont start the engine.

They will only flash once the connection to the app is made normally if you have power then the OBD is fine. 28 Gasoline 193HP 1999. Open the cover in the glove compartment and remove it.

Check the fuse box for any damage in the rear where the wires connect. First and foremost you should inspect. Okay if you have no power to the fuses that is why you have no power to the plug.

What is fuse number for 2008 x3 obd - BMW X3 question. 20D Diesel 150HP 2006. Diesel 148 HP 2005.

Connected to Bav Tech diagnostic tool and cannot readwrite fromto port. Check fuse number 5 in the passenger compartment fuse box it is a 10 amp that is the OBD connector power supply if that fuse is good just run power to pin number 16 of the. All the pins are in place.

The OBD Port is the location where you can plug in any OBD tool into the vehicle to pull vehicle information. 40L SOHC - I have no power to. Power requirements in the car is controlled by the power module.

Posted March 7 2016. Plugin the OBD-II scanner into the diagnostic port under the dashboard. In most cases these issues can be rectified and amended to allow you read the error codes.

Hello I have a no start issue with my BMW X3 2006 I am not getting any voltage to the Fuel pump wiring harness with the key on or when cranking I replaced the relay on the left behind the fuse box and still no power.

Obd2 Port Bmw X2 2018 Find Your Plug

Obdlink Lx Bluetooth Obd2 Bimmer Coding Tool For Bmw Vehicle And Motocycle Motoscan Plus 10pin Motocycle Bike Cable Code Readers Scan Tools Aliexpress